raspberry pi expansion board

With four LPF2 connectors, we can easily add a combination of Lego components to build robots and elaborate sensor-controlled devices. This programmable module is designed to be the core of a small robot, either as an auxiliary controller atop a Raspberry Pi base or as a complete control solution on its own. It is also available in the Server version pre-assembled in a standard 4 modules DIN rail case together with a Raspberry Pi 3 Model B. The board is however compatible with many more platforms, most of them open-source. It includes an LED status indicator, and 3 mounting holes for easy use in any project you have in mind. A video is found here. The ArduiPi is a board that brings Arduino world to Raspberry Pi and vice-versa. They are hoping someone will pick up the ball. Temperature, pressure and humidity sensors on the board; Two 1-Wire ports to connect the external temperature sensors DS18B20; Four high current outputs; Battery-backed Real Time Clock and Calendar; Small size - 2.1"x1.6" (53mm x 41mm). If you want to have it before the official launch, you can support the Indiegogo campaign. It controls two DC motors in forwards and reverse with pulse width modulation (PWM) which is useful for speed control and various stepper and solenoid control applications. The board includes the circuitry for the experiments with analog signals, sensor connections and circuitry to control the external devices as the relays, motors, high current LEDs. The board is based around PCA9685 PWM I2C LED controller IC from NXT and can drive each of the 16 outputs with 12 bit (4096 steps) duty cycle from 0% to 100%. Using arduPi library, you will be able to make programs in Raspberry with the same code used in Arduino. Not quite Skynet smart, so you can tell John Connor to stay at home and play with his Raspberry Pi. The AVR power supervisor allows the Pi to be powered on and off autonomously and also provides RTC and watchdog functionality. The CanBus is based on a couple of MCP2515 SPI controllers and ISO1050 tranceivers. This version ships as a partial kit; all surface-mount components are installed, but the included through-hole connectors are not soldered in. Can control up to 8 Motor for B+, VMX-pi Robot Controller/Co-processor Access Grove analog, digital, serial and I2C sensors from Raspberry Pi. SmartHome Modules are based on UniPi Neuron models, the Raspberry Pi computer is however replaced with another PCB containing additional I/O modules. The board can deliver a continuous 1.7A (2.5A peak) per motor. 128 GPIO Pi Pi Rtc Dio works with Rasperry Pi Model A, A+, B, B+ and the new Raspberry Pi 2 Model B. Pi Rtc DIO also works with the Banana Pro and the Banana Pi, however the Bananas already have an on-board RTC. Sized place for using PWM devices (switchable with on board power or external power). EZasPi (B) comes as a kit which includes an extra tall stacking header and mounting hardware that secures the board to the Raspberry Pi Rev.2 test mounting holes - keeping the board securely mounted on the Pi. This version (item #3118) does not include any through-hole components or connectors, allowing for customized assembly or standalone use. PiPLUS Multifunction I/O Extension Board is designed as versatile, general-purpose data acquisition and control module. a board with 8 relays and 8 input with a Raspberry Pi socket Each board is issued with an unique QR code, containing all necessary data for identification and component backtracking. Grove Base Hat for Raspberry Pi BattBorg is a power converter for your Raspberry Pi which allows you to power the Raspberry Pi off batteries. The board provides 2 motor control drivers with max current up to 3.5A, 8-bits data port with each pin setup as digital input /output or analog input, 10-bits ADC with up to 5 analog channels, 4 inputs for the sensor connections, infrared (IR) remote control. Comprehensive user's manual with exact steps for getting started is provided. DualSerial V 2.2 is composed by three blocks: a SPI-UART converter SC16IS752 and two UART-RS232 transceivers MAX3232. Schematics, PCB, sample code are on github. The default pin mappings make it easy to get started using our provided software, but the board also exposes most of the driver chips I/O pins for more specialized applications. This board has 2 relays, four 12 bit A/D inputs, and eight smart digital I/O ports. The RN2483 module complies with the LoRaWAN Class A protocol specications. Picade X HAT also provides sound using an I2S interface via the GPIO and a 3W mono amplifier outputs the audio to an external speaker (sold separately). AbioCard model A expansion board featuring a real-time clock (RTC), 8 bidirectional I/O lines, 8 12-bit ADC inputs, 16 PWM outputs at 97 kHz with 8-bit resolution. SainSmart offers the X100 expansion board "designed for ease of use", intended to make the RPi easier to use by providing various interface ports, such as a RS232 port, a HDMI to VGA converter (by using an included HDMI to HDMI male adapter, enabling the use of the VGA port; otherwise it is a HDMI input), a 3-port USB hub (one of the X100's USB ports connects to the upper USB port on the RPi itself, using an included USB to USB male adapter, thus providing power for the three other USB ports on the X100 board), SD and microSD memory card readers, an 8-channel Darlington driver and a GPIO port. For example, you can stack an EZasPi board between your Raspberry Pi and a RoboPi robot controller to add additional custom circuits to the Raspberry Pi. Breakout Garden is a Raspberry Pi HAT which offers a simple means to connect I2C devices. You can ideally use the OWFS software to support the 1Wir bus. This add-on board enables a Raspberry PiB+, PiA+, Pi2 or Pi3 to drive a pair of brushed DC motors. This LoraWan communication board for Raspberry Pi will allow you to use the Lora network to transmit information where you wish. This version ships fully assembled with connectors soldered in. Designed for the Raspberry Pi Zero, A+, B+, 2 and 3. RPIRTC v2 is a Real Time Clock (RTC) shield to keep your Raspberry Pi always on time. I might give it a try. forum thread showing 'paper mockup'. RPi-ShieldBridge An Arduino Shield Bridge with connector for a 2.8" TFT-Display with Touchpanel. The ADC Differential Pi is based on two Microchip MCP3424 A/D converters each containing 4 analogue inputs with up to 18 bit resolution. Other features include: For detailed specifications, go to https://pi-plates.com/product/daqcplate/, This board is a buffer between your Rpi and the real world, use it to flash LEDs on and off, drive motors, run sensors and all that other fun stuff.[2]. The standard UPS PIco is equipped with a 300mAh LiPO battery specially designed to enable safe shutdown during a power cut. It is mainly intended to remote control (using LIRC) and power off/on a mediacenter system. More information and a ready-to-buy kit be found here, Pi Jumper is the ultimate Raspberry Pi breakout board from [http://Mikronauts.com Mikronauts, - Works with Rasperry Pi Model A, Model B, Model A+ and Model B+, Raspberry Pi 2 Model B, - stacks on the Raspberry Pi (or any other Pi expansion board - such as RoboPi and EZasPi - with a stacking header), - 3.3V power regulated from the Pi's 5V supply (no more 50mA limit! Buzzberry is an interface board enabling expansion using the Buzz-Board modular system designed primarily for educational use. The board is based around the MCP23017 16-bit I/O expander from Microchip Technology Inc. Iono Pi by Sfera Labs is an extremely versatile I/O module that combines several digital and analog input lines, power relay outputs and support for standard interfaces like 1-Wire and Wiegand, typical of modern PLCs, with the powerful computing core of the Raspberry Pi. Lora Shield PI V 2.3 is a Raspberry Pi LoraWan expension It allows to connect to the operated LoRa networks called 'LORAWAN'. Users can program the servo control/camera movements, etc. This board also has the ability to interface with a Raspberry Pi, making the foundation for a complete Raspberry Pi-controlled balancing robot. The real time clock is based on DS3231 with internal oscillator I2C controller. The power supply is quite flexible and will accept anything from 8-25VAC or 8-42VDC. It works with the Pi2, Pi3 and Pi zero and any others with the same drivers and GPIO header. or www.advamation.com/products/embeddedpc/advaboard.html. Industrial computer based on the Raspberry Pi Compute Module, in a compact 2 modules DIN rail case, featuring dual SD card with high-speed switching matrix. To program Pibrella we can use Python or Scratch and quickly bring a project to life. Adafruit Industries announced in March 2012 the intention of making expansion boards for the Raspberry Pi under the "Pi Plate" name.[3]. It also provides signal buffering so that you can connect higher voltage servos to the board. Board size - 2.1"x1.6" (53mm x 41mm). | Thanks to the RS485 interface, extension modules can be used with any PLC unit supporting the RS485 bus and Modbus protocol - they are thus not limited only for use with Neuron units. With the help of the build-in MCU, a 12-bit 8 channel ADC is also available for Raspberry Pi. This leaves the Raspberry Pi free to perform tasks without worrying about timing, delays, or CPU intensive processes. The interface is a simple ASCII-protocol via the serial port. - eight low current LED's Also available on github in the kernel sources. The board provides direct connection to Raspberry Pi. Home From PridopiaExtra 1,2,4 UART HAT for Zero B+ 2B 3B For more info see introductory blog post and overview documentation page. The need for so few connections is due to the IO Expander using I2C, a two wire serial communication protocol. It also has five own GPIO-pins that is not supported by card firmware yet. Optionally, it can supply power 64GPIO-Pi with i2c/spi 2 type Cases - lots of nice cases to protect the Raspberry Pi. There are four 16-bit tachometers for DC speed control and the ability to use acceleration on all motors to prevent stalls and maximize torque. But to make the most of the Pi, it helps to have the right HAT (hardware attached on top). This version ships as a partial kit; all surface-mount components are installed, but the included through-hole connectors are not soldered in. C and Python libraries will be available at launch. with i2c/spi extra GPIO extension board 64/128 GPIO Board Mikronauts Pi Rtc Dio Real Time Clock & I/O Expansion Board that stacks on top of the Raspberry Pi and was designed by Mikronauts to add a real time clock, 32 digital I/O's and 3.3v power supply making one-off expansion circuits easier for everyone. Every EtherCAT slave requires a Vendor ID, we use the ID of SG Electronic Systems. Comes as a kit of parts that needs to be soldered. RPISIGFOX is a Raspberry Pi SigFox expension Shield delivered within a kit including a 4M Rail DIN Enclosure, an Antenna and an UFL cable. If you are feeling adventurous, you can even use some HATs with the original 26 pin GPIO models of Raspberry Pi. This can be useful when running the Pi on battery. Uninterruptible Power Supply with Peripherals and I2C control Interface | Aimed at driving large motors at up to 40V, current limiting to 55A, makes it powerful enough for even the most ambitious of projects. AbioWire+ is a 1-Wire adapter providing seventeen 1-Wire channels with ESD protection, three 1-Wire controller chips, and a real-time clock (RTC). All components are cheap standard electronic parts. The backpack also features 3 LEDs for status signals as well as two FTDI headers (one for the RPi and one for the XBee), as well as being able to host a 'normal' XBee module (though of course you can't use SPI with those). Strato Pi by Sfera Labs enhances the Raspberry Pi computer with several hardware features to make it suitable for use in professional and industrial applications where reliability and service continuity are key requirements. Directly to your inbox. Take a look at DoodleBorg - Our V1 Raspberry Pi tank to get an idea of what Diablo is designed to control. in addition, Only sn754410(or SN754410NE)motor drive if not use this can be used as a various raspberrypi extention shield. Can power RPi from ESC or external source. RoboPi Advanced Robot Controller Raspberry Pi expansion board from Mikronauts adds an eight-core 32-bit microcontroller running at 100Mhz to the Raspberry Pi in order to off-load hard real time I/O and allow more precise timing than Linux running on the Pi allows. Driver available with the stock Raspbian linux kernel, add the line "dtoverlay=audioinjector-wm8731-audio" to /boot/config.txt to get it running. The real time clock is based on DS3231 with internal oscillator I2C controller. But it's much smarter than your average relay board! la mode is an Arduino clone specifically designed to interface with the Raspberry Pi. It features VGA video acquisition, 2 250VAC 10A relays, 2 digital opto-isolated digital inputs, keyboard, mouse and remote storage emulation over USB, power management using 4 Ni-MH rechargeable AA batteries to assure rpi clean shutdown in case of power loss/failure. Robot Controller with direct connection to RPi is a versalite Mobile Robot Chassis controller board with I2C interface and wireless communication channel. Same-day shipping, worldwide, Development Boards (Programmable Controllers), Pololu Dual G2 High-Power Motor Drivers for Raspberry Pi, Motoron M3H256 Triple Motor Controller for Raspberry Pi, A-Star 32U4 Robot Controller LV with Raspberry Pi Bridge, A-Star 32U4 Robot Controller LV with Raspberry Pi Bridge (SMT Components Only), A-Star 32U4 Robot Controller SV with Raspberry Pi Bridge, A-Star 32U4 Robot Controller SV with Raspberry Pi Bridge (SMT Components Only), Dual TB9051FTG Motor Driver for Raspberry Pi (Assembled), Dual TB9051FTG Motor Driver for Raspberry Pi (Partial Kit), Pololu Dual MC33926 Motor Driver for Raspberry Pi (Assembled), Pololu Dual MC33926 Motor Driver for Raspberry Pi (Partial Kit), Dual MAX14870 Motor Driver for Raspberry Pi (Assembled), Dual MAX14870 Motor Driver for Raspberry Pi (Partial Kit), Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi, Balboa 32U4 Balancing Robot Kit (No Motors or Wheels), Aluminum Standoff for Raspberry Pi: 11mm Length, 6mm M2.5 Thread, M-F (4-Pack), Stackable 0.100 Female Header: 2x20-Pin, Straight, 0.100" (2.54 mm) Female Header: 2x20-Pin, Straight, Aluminum Standoff for Raspberry Pi: 18.6mm Length, 6mm M2.5 Thread, M-F (4-Pack), Stackable 0.100 Female Header with Extra 0.3 Spacer: 2x20-Pin, Straight, Machine Screw: M2.5, 6mm Length, Phillips (25-pack). It can be a simple IO expander, a 7 segment LED driver, provide servo and regular PWM outputs, or anything you can dream up that will fit into 1600 logic gates. The ADC Pi is based on two Microchip MCP3424 A/D converters each containing 4 analogue inputs with up to 18 bit resolution. The board can deliver a continuous 1.7A (2.5A peak) per motor. 128GPIO-Pi with i2c/spi two type There was a problem. Merging Lego and Raspberry Pi together is a genius idea. This programmable module is designed to be the core of a small robot, either as an auxiliary controller atop a Raspberry Pi base or as a complete control solution on its own. Attach LEGO Technic bricks to the BrickPi case to make awesome robots! Pi-Wire Homelabs are developing options for connection of a 1-wire bus to the RaspberryPi. Developed as part of the OpenEnergyMonitor project. MORE: Best microSD Cards for Raspberry Pi. The 1 Wire Pi Zero from AB Electronics UK is a communication board supporting the 1-Wire protocol. The Breakout Pi Zero is a useful and versatile prototyping expansion board for the Raspberry Pi Zero. - 1 x saved clock (RTC DS1338) by a super-capa recharged automatically by the raspberry pi when it is powered on. It's a low cost but powerful raspberry pi AI hat which assists raspberry pi run the AI at the edge, it also can work independently for edge computing applications. It allows you to cycle power on the Raspberry Pi without plugging and unplugging either your "wall-wart" power supply, or the micro-USB plug input to your Pi. The LAN9252 is a 2/3-port EtherCAT slave controller wi th integrated dual Ethernet PHYs Which Contain each to full-duplex 100BASE-TX transceiver and support 100Mbps (100 BASE-TX) operation. We do lose access to all of the GPIO pins when using the Explorer HAT Pro , but considering that this board provides so many different inputs / outputs and is designed with beginners in mind, we can forgive this loss. The board has an extra large prototyping area that is silk screened to clearly indicate signal busses. These G2 dual high-power motor drivers are add-on boards for the Raspberry Pi (Model B+ and newer), featuring pairs of discrete MOSFET H-bridges designed to drive two large brushed DC motors. 1-Wire 17Port The central device of the board is the SC16IS752 an I2C-bus/SPI bus interface to a dual-channel high performance UART offering data rates up to 5 Mbit/s. RabbitMax Flex is a multi-purpose Raspberry Pi add-on board for prototyping IoT and home automation applications. Furthermore, a lot of detailed information about the DAB ensembles can be read-in and decoded. For more information, visit the software choice manual. Heber xSpin Youtube clip of first prototype. It is an Open Hardware Design. The kit includes a pre-prepared strip-board, all the necessary components and cables, and a very complete full-colour manual with lots of code examples. When buying a Raspberry Pi HAT, ask yourself these questions: For general purpose experiments in electronics nothing can beat Pimoroni's Explorer range of boards. The added Hack Header provides a connection to the I2C interface, handy for adding extra components. The real time clock is based on DS3231 with internal oscillator I2C controller. The Raspberry Pi XBee ZB SMT Backpack by bootc is a carrier board for Digi XBee ZB SMT modules. They have released the PCB layout and all documentation for free on their website. The Grove AI HAT for Edge Computing is built around Sipeed MAix M1 AI MODULE with Kendryte K210 processor inside. This add-on board enables a Raspberry Pi (Model B+ or newer) to drive a pair of brushed DC motors. The Pi-BT-COM-Pi provide RS232 - 3.5mm serial console Port - Bluetooth console Port - RTC function in one board Expansion Boards - GPIO plug-in boards providing additional functionality. Its ATmega32U4 AVR microcontroller comes preloaded with an Arduino-compatible bootloader. - eight switch dip switch, For more information, please visit the SchoolBoard 2 product page. RPi RS232 Breakout Board is a simple RS232 breakout board for the Raspberry Pi. A GPIO header replicator board for your Raspberry Pi. The preloaded software provides the DC motors and Servo motors PWM control, sensor data reading and communication with RPi by I2C interface or wireless channel. EtherC V1.6 is an extension board for RaspBerry Pi based on LAN9252 EtherCAT Slave produced by Microchip. He has worked with the Raspberry Pi Foundation to write and deliver their teacher training program "Picademy". RPIDOM v2 is the ideal expansion card for developing a standalone home automation server, measuring the power consumption of your home and / or production of your photovoltaic system. The GrovePi from Dexter Industries is a slide on board for the Raspberry Pi that allows the Raspberry Pi to communicate with hundreds of plug and play Grove Sensors. Iono Pi complies with CE directives for EMC, Electrical Safety, Emission and RoHS. The board also has the ability to interface with an added Raspberry Pi, making the foundation for a complete Raspberry Pi-controlled Romi robot. XLoBorg is a 3 axis accelerometer and 3 axis magnetometer which can be used as a compass and would be especially useful in UAV/drones. Touch the banana and the note for that key is played. Older versions of the X HAT, which may still be on sale, use a microUSB connector that only has enough juice for a Pi 3 or earlier. The RPIDOM v2 offers the following features: - 2 x tele-information connectors for opto-isolated EDF type meters, - 1 x 1-wire home automation bus connector (1wire hardware and protected, supported by official components Maxim / Dallas DS2482). If you intend to use a HAT with the new Raspberry Pi 400 then you will also need a breakout connector, such as Pimoroni's Flat HAT Hacker HAT. Perhaps most importantly, it has four built-in analog inputs so you can attach analog devices such as potentiometers and joysticks without the need for an additional analog-to-digital converter chip (something the Pi lacks on its own). These are different to the normal XBee modules because they are surface mount and additionally can interface to a host using SPI as well as serial. sound / tone generator, DTMF generator. The Pi-Plates DAQC (DAC-SEE) adds a rich set of input/output options to your Raspberry Pi. Buffer Board How to make a Pi Buffer on Veroboard. DiscoHAT was developed to be used together with QLC+, an Open Source light and sound control software that is absolutely AMAZING. TRACOPOWER 5V & 3.3V (TSR-1-2433 & TSR-1-2450) DC/DC converter up to 96% efficiency - No heat-sink required ( for longer battery life) 8. The GitHub community site contains many ready made cores that you can download and use directly. Four inputs, and four outputs can be used with external components, including motors. The popular culfw-firmware lets you interact with FS20, Homematic, Intertechno or similar actors and sensors - easily using FHEM-home automation server. with i2c/spi extra GPIO extension board 32 GPIO Board For more information about EZasPi (B), please visit the EZasPi (B) product page. More information: Technical Specifications. The equivalent of a high end sound card for the PI. It needs a kernel module to work. On-board hardware includes dual motor drivers that can deliver 1.8A per channel and an efficient voltage regulator that allows the controller to work with a 2.7V to 11V input voltage, along with level shifters that enable it to interface with a Raspberry Pi. If you want to build a retro arcade machine, complete with an arcade joystick and buttons, the Pimoroni Picade X HAT is the board to get. Now available to purchase in kit form on Kickstarter here - Pi Crust Kickstarter, Piface is simpler than the RPi Gertboard (it's aimed at less experienced users), but also intended to connect to PCs and Android to be platform agnostic. In addition, we will continue to add new compatible modules to the compatible list, the more you use, the more grove will be added. BIG Order Form It is also compliant with part 15 of the FCC rules (Class A), ICES-003 (A) and CISPR 32:2015 (Class A) standards. Inbuilt microphone on the board, for voice commands or other tasks. Chip oscillator locked for low jitter operation, Driver available with the stock Raspbian linux kernel, 3.5 mm jack (4-pole) for a headset/boom mic combination for gaming or VoIP applications, 3.5 mm jack stereo line input for connection to devices such as digital audio players (iPod etc.) This is a great way to take your skills to the next level and learn how to layout a circuit. Exclusive features include a real time clock, battery backed static ram, a Dallas chip (for unique board identification), 2 serial communication ports, a powerful audio amp and a independent dedicated on board processor.

• Aerie Offline Longline Sports Bra
• Nostalgic Warehouse Switch Plates
• Mccleary Pass Insulated Jacket Women's
• Arabescato Carrara Stacked Stone
• 2011 Jeep Grand Cherokee Limited Specs
• Spinning Engravable Men's Ring
• Coppertone Sport Spf 50 Ingredients
• Fender Bass Pickguard
• Redhead Midweight Gloves