Continue to Numbers Installation . Adequately protect adjacent surfaces with paper. Note: decals should not be applied on rough surfaces or in wet, freezing conditions. Note: decal should not be applied on rough surfaces or in wet, freezing conditions. Allow paint to dry. Rinse gently with clean, fresh water. For decals, it doesnt get any easier than peel-and-stick! Keep guidelines straight, maintain your desired spacing. Press numbers firmly onto mailbox. Take care not to scratch the face of the plaque. Align templates vertically using labeled vertical guideline. Push plaque into holes. Aged Bronze Flush Mount House Number 1, 6 in. Local store prices may vary from those displayed. Aged Bronze Screw On House Number 0, 6 in. Use a soft cloth and a mild household detergent solution to remove dust, salt, and other deposits. All Rights Reserved. Peel off the front transfer film. For vertical arrangement, skip to step 3A. Aged Bronze Screw On House Number 5, 6 in. If so, place on a soft surface. Use a soft cloth and a mild household detergent solution to remove dust, salt, and other deposits. Note: Steel studs must be fully concealed to protect from the elements. Aged Bronze Screw On House Number 2, 6 in. Use a ruler to measure the space between each number. Masonry, concrete, and stone installations may require a hammer drill. Use 11/64 drill bit or specialty 3/16 bit for masonry and rock. Slowly peel off the clear, front transfer film. Spray paint stencil using multiple, light coats. Dry with non-abrasive towel. For decals, it doesnt get any easier than peel-and-stick! Peel off the number backing and align with tape guide. If so, place on a soft surface. Please note that these letters are mounted flush on the wall. Aged Bronze Screw On House Number 6. Light tapping may be required. Instructional video of how to install your modern house numbers on a stucco wall. Gather supplies: tape and ruler (not included). Take care to not scratch the face of the plaque. Dry with non-abrasive towel. Light tapping with a rubber mallet may be required. CARING FOR YOUR PRODUCTS: To extend the effective life of your numbers, clean them every six months or every three months in coastal or industrial regions. Push number into holes. Press stencil decal firmly with even pressure onto concrete at desired location. For horizontal arrangement, go to step 2A. Need Help? Step 4 Push number into the mounting holes. Use clear tape to connect individual templates together. Drill holes according to template. Take care not to over spray. Take care to not scratch the face of the number. Push studs into pre-drilled holes on the back of the plaque. Set! Note: Curb stencil should not be applied in wet or freezing conditions. Ready? Tape all edges. Skip to step 4. Gather supplies: house numbers, template, studs, spacers, (not included: tape, epoxy, rubber mallet, drill, level). Ready? Step 2 Screw in the threadedstuds into the back of the number. Slide spacers over studs. Gather supplies - curb stencil decal, (not included: spray paint, paper roll and masking tape). Get exclusive access to new products and deals. Drill holes according to marks on the template - use 3/16" drill bit. Note: Steel studs must be fully concealed to protect from the elements. Overlap of paper template edges is to be expected. Apply even pressure along the entire surface. Remove tape. With your number, letter, or plaque order. Arrange individual paper templates in desired order. Overlap of paper template edges is to be expected. Take care not to scratch the face of the number. No spacers were used. Use a level to align template. Go time! Apply a thin layer of epoxy to one end of the stud. Apply a thin layer of epoxy to the end of the exposed studs. Clean and dry the mailbox surface. Aged Bronze Screw On House Number 1, 4 in. With your order, you'll receive our custom-made modern house numbers/letters, threaded aluminum studs, 1/2 inch aluminum spacers (which give your numbers that "floating" look), pre-printed mounting template, and printed instructions on an easy step-by-step process for installing your modern house numbers. Keep vertical guidelines aligned. Masonry, concrete, and stone installations may require a hammer drill. Proudly Made in USA. Set! For a worry-free install, get acquainted with our step-by-step installation instructions! Products shown as available are normally stocked but inventory levels cannot be guaranteed, For screen reader problems with this website, please call 1-800-430-3376 or text 38698 (standard carrier rates apply to texts), 6 in. Rinse gently with clean, fresh water. Unsubscribe at any time. Please call us at: 1-800-HOME-DEPOT (1-800-466-3337), Please enter in your email address in the following format: you@domain.com. Use of this site is subject to certain Terms Of Use. Align X marks on each template at top and bottom to achieve equal spacing between each number. Go time. Matte Black Aluminum Floating or Flat Modern House Number 1, 6 in. Aged Bronze Screw On House Number 4, 6 in. Push studs into pre-drilled holes on the back of the number. Determine your desired spacing between numbers on the available space. This is your drilling guide. The below Instructional video demonstrates how to install aluminum powder coated letters on an office wall. Gather supplies: mailbox numbers, (not included: tape, and ruler). Step 3 Slide spacers over studs and apply epoxy or clear siliconeto the end of the stud. 2021 Modern House Numbers Aged Bronze Screw On House Number 3, 4 in. Matte Black Aluminum Floating or Flat Modern House Number 2, 6 in. Carefully remove template. Clean surface of all loose debris. Tape template at desired location. Aged Bronze Flush Mount House Number 2, 6 in. Light tapping may be required. Align templates horizontally using labeled guidelines at top and bottom. With your number, letter, or plaque order,well include instructions, mounting hardware, and a handy drilling template. Light tapping with a rubber mallet may be required. Overlap of paper template edges is to be expected. Gather supplies: plaque, template, studs, spacers, (not included: tape, epoxy, rubber mallet, drill, level). For a worry-free install, get acquainted with our step-by-step installation instructions! Peel off number backing. Measure the desired number location. Installation Instructions Step 1 Tape the paper mounting template to the desired location and use a level to align template. Once dry, slowly remove stencil. well include instructions, mounting hardware, and a handy drilling template. 2000-2022 Home Depot. CARING FOR YOUR PRODUCTS: To extend the effective life of your plaque, clean every six months or every three months in coastal or industrial regions. Place a piece of tape to align the bottom edge of the numbers.
- Detachable Lace Train
- Becca Long Sleeve Crop Top White
- Weathertech Kitchen Floor Mat
- Copper Coil Tubing Near Me
- Best Hard Shell Carry-on Luggage
- Urban Decay 24/7 Eyeshadow
- Handbag Manufacturers
- Toyota Tundra V6 For Sale Near Florida
- Posh Peanut Sweatshirt
- Bissell Pet Stain And Odor Remover Instructions
- Warn 91801 Powerplant 12
- Gel Nail Polish With Uv Light
- Brakebill Led Frameless Lighted Bathroom Mirror
- Bianchi Oltre Xr2 Frame Weight
Share